Sansin Woodforce Clear
$74.99 – $344.99
Sansin WoodForce Clear is a low-VOC, breathable wood treatment that protects vertical exterior wood from moisture, UV damage, and blackening—without forming a film or altering its natural look. Ideal for log homes, siding, timbers, and wood roofing, it allows wood to weather evenly and beautifully over time while remaining easy to maintain.
Sansin WoodForce Clear
Durable Clear Wood Treatment for Natural Weathering
Sansin WoodForce Clear is a high-performance exterior wood treatment designed to protect wood while allowing it to weather naturally. It delivers exceptional water repellency, UV resistance, and protection against blackening and rot—without forming a film or altering the natural look of the surface. Ideal for log homes, siding, timbers, and wood roofing, WoodForce Clear preserves the integrity of wood in all climates while enabling an attractive, even patina to develop over time.
What Makes Sansin WoodForce Clear Unique?
Unlike traditional exterior finishes, WoodForce Clear does not mask the surface with pigment or film. It penetrates deep into the wood to provide breathable, long-term protection while allowing natural weathering to occur. This approach minimizes surface degradation and blackening while giving architects and builders the flexibility to showcase natural grain and aging. With low VOCs and easy maintenance, it’s a long-lasting and environmentally responsible choice.
Key Benefits
- Allows wood to weather naturally and evenly
- Protects against water, UV exposure, and blackening
- Non-film-forming and breathable
- Low VOC, Red List and CARB compliant
- Ideal for clear, unpigmented finishes
- Easy to maintain and reapply
Where to Use
- Log homes and timber frame exteriors
- Wood siding and vertical cladding
- Wood shingles and roofing
- Board-and-batten and exposed beams
- Fences and vertical trim
Application Notes
Surface Preparation Requirements
- Surface must be clean, dry, and free of previous coatings
- Sand smooth wood with 60–80 grit just prior to application
- Power wash or clean with Sansin Multi-Wash as needed
- Apply only to bare or properly stripped wood
Application
- Apply to saturation using brush, spray, or flood coat
- Use a large China bristle brush to distribute product and avoid puddling
- Apply first coat at 6–8 mils wet film thickness
- Allow to dry approximately 2 hours in favorable conditions
- Apply second coat at 4–6 mils for enhanced protection
- Do not apply in direct sunlight or when rain is expected
Coverage
Surface Type | Estimated Coverage per U.S. Gallon |
---|---|
Rough-sawn or porous wood | 200–250 sq. ft. |
Sanded or smooth wood | 300–350 sq. ft. |
Maintenance Required
Vertical surfaces treated with WoodForce Clear require maintenance every 4–6 years. Clean surfaces using Sansin Multi-Wash and rinse thoroughly. Reapply one maintenance coat of WoodForce Clear to maintain protection. Over time, untreated maintenance will result in natural darkening as wood ages. Routine maintenance ensures an even, attractive weathered appearance and prevents premature degradation.
Frequently Asked Questions
- What is Sansin WoodForce Clear used for?
- It is used to protect exterior wood while allowing it to weather naturally without pigment or film.
- Does it change the color of the wood?
- No, it is a clear treatment that preserves the wood’s natural tone and allows weathering over time.
- Can I apply WoodForce Clear over a previous stain?
- No. It must be applied to bare, properly cleaned or stripped wood only.
- How long does it last?
- Typically 4–6 years before maintenance is required, depending on exposure and climate.
- Is it breathable?
- Yes. It allows moisture vapor to escape while repelling liquid water.
- What type of wood is it best for?
- It’s ideal for logs, siding, shingles, timbers, and other vertical exterior wood surfaces.
- Can I use this on horizontal surfaces?
- No, it is formulated for vertical wood only.
- How do I apply it?
- Apply by brush, spray, or flood coat to saturation, and brush out runs or puddles.
- What’s the drying time between coats?
- Approximately 2 hours under ideal conditions (21°C, 50% RH).
- What kind of cleanup is required?
- Clean tools with soap and water. Do not allow product to freeze during storage.
Downloads
Weight | N/A |
---|---|
Dimensions | N/A |
Select Size | 5 Gallons ,1 Gallon |
Reviews
There are no reviews yet.